The bolt handle is curved at approximately a 45-degree angle, unlike the K98k, which is turned down at an angle sharp enough to prompt the need for a cutout in the stock to accommodate it. The rear sight gets hot, too since it’s mounted on the barrel through a slot in the upper handguard. Maybe not a big deal, but the barrel gets damned hot after a few rounds and that extra protection is nice when handling the weapon after putting it through its paces. The upper handguard on the M48 covers the barrel all the way back to the receiver, while the K98k only goes back to the front edge of the rear sights. Several features of the Zastava rifles are different too. According to my scale, my M48B comes in at 8.2 pounds unloaded.Īn attitude of gratitude is never a bad thing. The M48 is in the same range, with 8.6 pounds being the standard. The listed weight for the K98k is 8.2 to 9 pounds. The weight of both rifles can vary by a few ounces either way. The M48 is not quite an inch shorter in overall length, measuring 42.75 inches, with a 23.25-inch barrel compared to 23.62 inches for the K98k. The M48 was not a carbon copy of the K98k, though there are similarities. Preduzece 44 was later known as the “Red Banner” plant. Even though the bolt action infantry rifle was pretty much obsolete by then, the Yugoslavians set up the Preduzece 44 facility (part of Zastava) to manufacture what became the M48 Mauser variant. The KAR 98 was the standard-issue infantry rifle for the Wehrmacht right through the end of the war. As part of the reparations Germany had to pay after World War II, Yugoslavia received tooling and equipment to make the Mauser 98, specifically the Karabiner 98 kurz (K98k or KAR 98) version. One of the best examples of the Mauser series was not manufactured in Germany, but in Yugoslavia in the late 1940s and 1950s. The Zastava M48 is among the last bolt action infantry rifles made and it just might be the best a Mauser can be. Mauser sued over it too, but the legal wranglings got sidetracked by a little dust-up known as World War I. I include the M1903 Springfield in that latter group since most of us know that the ’03 action was essentially a Mauser copy. I love my Mosins too, but the truth is that they’re garbage next to any Mauser 98 variant in reasonable condition. Sorry if that pisses off any Mosin-Nagant-o-philes out there, but it’s a fact. Sure, there are other great designs like the Swiss K31 and British SMLE, but no series of rifles has been more consistently excellent than the ones that are based on the Mauser 98 action. Mausers are the gold standard for Milsurp rifles for many people, myself included. Twist it anti clockwise until the screw comes free.The Zastava M48 Mauser - there are many like it, but this one is mine! Grip the top of the screw extractor with a wrench. The screw extractors are similar to a screw but have a reverse thread.How to remove a screw using a screw extractorAlways select a drill bit that is slightly smaller than the screw you want to remove.Attach to the drillLine the drill bit up with the centre of the screwWork slowly to drill a hole for the extractorPlace the spiral end of the extractor into the hole you have drilled.Twist the extractor anti clockwise until you cannot turn it anymoreTwist the extractor with a wrench or drill. The easiest way to remove the screws before replacing with a new one, is to use a specialist tool such as a screw extractor. This brings any work or project to a halt. You can learn more in our complete guide to screw extractors.Why use a Screw Extractor? Screws can break, rust or become stripped and need to be replaced. They can be driven manually using adjustable spanners or vice grip pliers or by using a hand-held power tool. Screw Extractors A screw extractor is a tool for removing broken, damaged or seized screws.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |